RM22903 | Kit Stator Pickup Pulsar Coil + Ignition Source Coil for Yamaha YFM 200 225 250 Moto 4 1986-1991 |
C$89.48
Ignition Source Coil Dimensions:
Height: 27 mm
Length: 35 mm
Width: 30 mm
Other Specifications:
Number of wires: 2
Number of terminals: 2
Wires length: 500 mm
Wire to Wire Resistance:
Red to White : 315 ohms +/-20%
Pickup Pulsar Coil Dimensions:
Height: 19 mm
Length: 23 mm
Width: 20 mm
Bracket center to center: 35 mm
Wires length : 915 mm
Other specifications:
Number of wires : 2
Number of pins: 2
Wire to wire resistance:
Black to Grey = 200 ohms+/-20%
Kit Brand New Pick Up Pulsar Coil + Ignition Source Coil
- Often unavailable from the OEM manufacturer
- All shipped products are tested
We offer a brand new ignition source coil for you to repair your stator.
- Highest grade of lamination materials
- Highest grade of copper winding, resistant to 200 degrees celcius
- Works with all other OEM parts
Brand new pick up coil 200 ohms
- We offer a brand new pickup/pulsar coil for you to repair your stator
Ignition Source Coil:
Step 1 : Take the ignition cover off. Are the remplacement parts similar?
Compare the replacement part to the original. The remplacement part should match, including the mounting hole locations, If not: Double check the application listing with your bike.
Step 2 :Take note of the wire colors of the original stator wires and disconnect them from the wiring loom.
Step 3: Remove the flywheel using a proper puller tool.
Step 4: Remove the baseplate with the original coil.
Step 5: Remove the screws that secure the coil and take the coil off.
Step 6: Cut the original wire close to the original coil. Take a good look at how the wire is connected to the coil.
Connections: Connect the old wire up to the new coil. Use a soldering iron and resin core solder. (the type used in electrical applications).
Step 7: Mount the coil onto the baseplate, fit the screws using locking compound on the threads and TIGHTEN THE SCREWS SECURELY!
Step 8: Refit the stator baseplate. Ensure the wires CANNOT TOUCH THE FLYWHEEL! (especially on the inside of the flywheel)
Step 9: Refit the flywheel. Tighten the bolt to specified torque.
Step 10: Fit the ignition cover.
TROUBLESHOOTING:
Engine will not start: Sometimes the source coil wires are reversed. Swap the connections, re-solder the wires and the engine should start. If the engine still does not start, and before calling technical support, performs a few basic tests:
1) Re-check the connections. Make sure you carefully solder the connections. Twisting wires together or taping wires will cause engine inoperability.
2) Check the engine for spark
3) Is fresh fuel in the gas tank?
If you still cannot get the engine to start, have all your testing information ready for a technician prior calling.
Pick Up Pulsar Coil :
Not following these instructions may result in damaging the part or other components on your vehicle.
- By using a small soldering iron weld the wires to the ones on your OEM wiring harness.
- Insulate your solders with heat shrink.
- Before attempting to start your vehicle, adjusting the air gap is necessary for certain models.
- Rotate the fly wheel by hand so the raised node is lined up with the pick up /pulsar coil and adjust as close as possible, but no less than 0.010’’.
- If no spark or erratic spark, switch the wires at the plug.
| Weight | 0.10 kg |
|---|---|
| Dimensions | 9.906 × 6.096 × 4.57 cm |
| Brand |
RMSTATOR |
| Fitment Type |
Guaranteed Fit |
OEM AND OTHER PART NUMBERS
OEM NUMBER
- RM22903-R00, RM22903.R00, RM22903 R00, RM22903R00
ADDITIONAL NUMBER
- RM22903
DO NOT MANUFACTURE PARTS, DESIGN PERMANENT SOLUTIONS
We cultivate our actions towards finding permanent solutions. There is no way, us, as customers, would like to replace a part again and again. This mindset forces our team to design to fix, to conquer these pesky electrical failures in powersport.
GOOD DESIGN PRODUCE GOOD PRODUCTS. EFFICIENT DESIGN CREATES STELLAR PRODUCTS.
We are committing to innovate in finding clever ways to design more efficient parts that produce better results than any other part on the market.
WE ALL ARE CUSTOMERS ELSEWHERE.
In our shopping journey for buying our daily goods, we all expect to be treated with respect in a relation that makes us feel welcomed. Our team is encouraged to elevate that standard even higher and to provide all the information necessary for an easy and reliable installation.
OWN YOUR CUSTOMER PAIN LIKE IT IS YOURS
We own powersport rides ourselves. We feel the pain of dealing with unsolvable troubleshooting on our rides. We are committed in manufacturing complete solutions to known or I-would-never-have-suspected issues that are plaguing your rides... and ours.
