RM22808 | Kit Stator 200 W + Regulator Rectifier + Ignition Coil + Flywheel + Flywheel Puller for Yamaha YFZ 350 Banshee 1995-2006 |
C$505.76
Dimensions Stator :
Interior diameter: 103mm
Exterior diameter: 34mm
Thickness: 27mm
Length of wires stator to grommet: 60mm
Length of wires grommet to plug: 520mm
Length of pickup coil’s wire to grommet: 80mm
Other specifications :
Number of wires: 6
Number of plugs : 3
Number of pins: 6
Wire to wire resistance :
Alternator : Yellow to Black = 0.4ohms +/-20%
Pickup: White/Green to White/Red = 115ohms +/-20%
Source : Green to Red = 12ohms +/-20%
Dimensions AC Regulator:
Height: 20 mm
Length: 45 mm
Width: 45 mm
Other specifications:
Number of terminals: 2
Wires length: 130 mm
External Ignition coil
Distance between fixation holes: 90mm
Available on backorder
Brand New Kit Stator 200W + AC Regulator + External Ignition Coil + Flywheel + Flywheel Puller
- Direct replacement to your original unit
- Plug-and-play, direct fit, easy installation
- All shipped products are tested
Brand New High Output Aftermarket Stator 200W :
- Highest grade of lamination materials
- Highest grade of copper winding, resistant to 200 degrees Celsius
- Pick up pulsar coil included
- Connector included
- Rubber grommet included
- Back Plate included
For a limited time we are including a FREE Tympanum AC regulator required to run the extra wattage supplied from our 200W stator :
- 12 Volts regulator used by Baja winners
- For use with all standard halogen and quartz lights
- Precise voltage control, eliminates light burnout
- Reduce flickering and dimming
- Simple installation
- Works with all other OEM parts
- Rated at 225 watts
External Ignition Coil
- Highest grade of lamination materials
- Spark plug cap(s) included
Improved Stronger Magneto Flywheel Rotor
RMSTATOR is offering a new replacement flywheel with stronger magnetsfor your Banshee. This flywheel can be used as a direct replacement to the OEM.
We suggest combining it to our 100 or 200 watt stator as it will run the lights better in the lower rpm’s.
Before installing your new stator/flywheel
- Check the AC output of the stator.
- Replace any burned or corroded connectors on stator and regulator/rectifier
- Check and repair any melted wiring.
- Use hi-temp dielectric grease on all connectors
Our stator may use a different wire color code than your original.
All of the wires are installed in the correct order; please do not change any of the wiring configurations.
This stator is designed as a direct plug-in replacement and should be used as such.
When bolting stator in, always use locking compound.
If our stator includes a pickup coil, always make sure the air gap is correct upon installation; we suggest as close as possible no less than 0.010″.
Check to be sure that all of the following is done to ensure that your AC regulator rectifier is installed properly:
- Bolt regulator to frame
- Ground Black wire to Frame or Harness ground
- Connect yellow wire to AC output lead of the Stator
External Ignition Coil:
Remove the yellow wire from the external ignition coil, if it is not applicable to your model.
| Weight | 3.49 kg |
|---|---|
| Dimensions | 16.002 × 7.112 × 16.00 cm |
| Brand |
RMSTATOR |
| Fitment Type |
Guaranteed Fit |
OEM AND OTHER PART NUMBERS
OEM NUMBER:
- RM-22808, RM.22808, RM 22808, RM22808
ADDITIONAL NUMBER
- RM22808
DO NOT MANUFACTURE PARTS, DESIGN PERMANENT SOLUTIONS
We cultivate our actions towards finding permanent solutions. There is no way, us, as customers, would like to replace a part again and again. This mindset forces our team to design to fix, to conquer these pesky electrical failures in powersport.
GOOD DESIGN PRODUCE GOOD PRODUCTS. EFFICIENT DESIGN CREATES STELLAR PRODUCTS.
We are committing to innovate in finding clever ways to design more efficient parts that produce better results than any other part on the market.
WE ALL ARE CUSTOMERS ELSEWHERE.
In our shopping journey for buying our daily goods, we all expect to be treated with respect in a relation that makes us feel welcomed. Our team is encouraged to elevate that standard even higher and to provide all the information necessary for an easy and reliable installation.
OWN YOUR CUSTOMER PAIN LIKE IT IS YOURS
We own powersport rides ourselves. We feel the pain of dealing with unsolvable troubleshooting on our rides. We are committed in manufacturing complete solutions to known or I-would-never-have-suspected issues that are plaguing your rides... and ours.
